Best Bass Fishing Spots in U.S.

Americans are blessed with plentiful bass fishing holes (with the exception of Alaska, but, hey, 49 out of 50 isn’t bad). I recently stumbled upon an article listing the top 25 bass fishing spots in the Union. From my own experience, I would say there are some more deserving areas that could be on the list, but overall, the author did a good job.

He listed Falcon Lake, TX, Lake Okeechobee, FL, and even Georgia’s Lake Lanier. California had quite a few spots on the list, including Lake Amidor, Castaic Lake, and The San Joaquin Delta. With a little bit of know-how, a good lure, and two cycle oil in your engine, whatever watering hole is closes to you can become the best bass catching spot.

Did you like this? Share it:

Blending Synthetic and Regular Oil

I’ll admit that I used to be part of the crowd that believed that synthetic and regular oil could not be mixed. I falsely believed that mixing the two would cause congealing, foaming, and leaks. All of that turned out to be false.

In fact, some major manufacturers produce blended oils known as semi-synthetics. These combination oils work because synthetic oil is based off of regular crude oil and then hydrocracked to eliminate impurities. If you already have synthetic oil outboard motor and regular motor oil on hand, then you can mix your own semi-synthetic. Just be sure to read up on proper procedures before attempting the combination.

Did you like this? Share it:

Beneficial Properties of Synthetic Oil

There are boaters who believe that using synthetic oil instead of regular oil is akin to using margarine instead of butter. It may look the same, but does it really do the trick? As a former doubter, I can attest to the beneficial properties of synthetic oil.

Several years ago I made the switch to synthetic 2 stroke outboard oil. I learned that many synthetic oils are made with ash-less components to prevent fouling. The anti-gel properties also proved better than the regular oil I was using. Plus, the synthetic oil came dyed blue which made detecting the oil in fuel a lot easier.

Did you like this? Share it:

Friendly Family Competition

My brothers and I grew up boating on the Chesapeake Bay. Though most of us live in urban areas now, we still go home for all the major holidays. Our dad still owns a small fleet of boats that he needs help winterizing each year.

To make it less of a chore, my brothers and I have made winterizing the boats into a competition. The first brother to finish winterizing their boat properly wins. Dad, of course, gets to be the judge. He is a particular stickler for making sure that we haven’t shortchanged any areas that need outboard oil.

Did you like this? Share it:

The Mistakes of “Gold Rush”

The Discovery Channel has some fairly interesting reality television programming, including the series “Gold Rush” (previously known as “Gold Rush: Alaska”). I was watching one of the early episodes from season two and was simply appalled by what I saw. The crew did not winterize their big equipment at the end of last season, meaning when they arrived back at their claim, much of their heavy machinery was heavily rusted.

Naturally, there was concern as to weather the machinery would start at all. By some miracle it did, but I would never advise letting any piece of machinery simply rust away during the winter months – especially not in a climate like that of Alaska! Take this as a warning to winterize all boats now before the worst of winter sets in. Don’t forget to stock up on outboard motor oil while you’re at it.

Did you like this? Share it:

Choosing Marine Diesel Engine Oil

Special marine grade oil is needed for diesel marine engines, as they typically carry high loads for extended periods of time. The National Marine Manufacturers Association tests diesel engine oils and gives recommendations based on those tests. The oils tested may be entirely synthetic or partially synthetic.

NMMA-certified oils include: oil TC-W3 amalie, FC-W and FC-W (CAT). TC-W3 is used with two-stroke engines, FC-W with four-stroke engines, and FC-W(CAT) with four-stroke engines that have exhaust treatment catalyst systems. When selecting diesel oil, be sure to consider added characteristics

Did you like this? Share it:

How to Disconnect a Mercury Outboard Motor Oil Pump

To , you will need pre-wired paper tags, an oil storage container, and duct tape. Start by locating the oil inlet line that runs from the oil tank to the oil pump. Tag the line.

Pull out the oil inlet line by hand from the pump and cap it with your thumb. Drain the mercury outboard oil into a storage container. Use duct tape to cap the line. Tag the oil outlet line which runs from the pump to the fuel system. Pull the line from the pump, and then cap the line with duct tape to prevent contamination.

Did you like this? Share it:

Oil Storage Drums

If you’re like me, then you try to save money by ordering your outboard motor oil in bulk. While this is a great money saver, you need to be careful with how you store oil. Drums can be made of several materials, including polyethylene and steel. You need to check with the manufacturer to make sure that the container you use for storage is appropriate for the oil it contains.

An incorrect storage drum can cause damage to the oil itself. The wrong storage drum can also become corroded and leak oil everywhere, thus hurting the environment and your wallet. The moral of this story is, give your mercury oil 55 gallon drum guy a call when you place your order to make sure everything is kosher.

Did you like this? Share it:

Shrink Wrapping Your Boat

Shrink wrapping your boat helps protect it during the cold winter months. All you need is a boat shrink wrap kit, a heat gun, and a ladder (depending on the size of your boat). Most of these items can be ordered online or purchased at a boating supplies store.

Take care of the engine, mercury oil, and other necessities on the boat and position the vehicle where you want it to stay for the season. Pad sharp corners that could potentially puncture the shrink wrap. Put up support poles for the shrink wrap to adhere to, and then unroll the shrink wrap over the boat. Use the heat gun to tighten and seal the shrink wrap. Check your work for any holes, patch up those holes you find, and finally install self adhesive vents to keep mold from forming under the wrap.

Did you like this? Share it:

Biofuels Debate Rages On

Coming to market soon is a 15 percent blend of ethanol fuel mix. The new blend has outboard marine engine producers up in arms. An engineer from Mercury Marine Corp. was scheduled to testify before a congressional committee last week regarding the damage the new biofuel blend has on outboard engines.

In one of the Department of Energy approved tests, a 200-horsepower outboard engine’s bearings on a piston disintegrated after 300 hours of operation. Meanwhile, the outboard engine using mercury engine oil and fuel mixture did not experience any damage. Supporters of the new blend counter that the tests are statistically irrelevant because so few engines were used. Supporters also claim that the engines tested were not calibrated properly for the new 15 percent ethanol blend.

Did you like this? Share it:

Cleaning Mercury Marine Carburetor, Part II

Let’s pick up from where yesterday’s post left off. After removing the carburetor, you’ll next want to clean the jets with a jet pick. Try to remove as much oil gel as possible before washing the jets in carburetor cleaner. Clean the gunk out of the fuel bowl, too.

Next, take your . This will remove any buildup that has managed to stay put. Wear safety goggles to protect from particles blowing into your eyes. Stay tuned for part III tomorrow, and don’t forget to stock up on Mercury 2 stroke oil!

Did you like this? Share it:

Fast Facts: Marine Engine Oil

Why use marine engine oil? Isn’t all oil the same? In a word: no. The oil you use in your car is not suitable for your boat.

Boats have a closed loop cooling system, unlike automobiles. Boats, obviously, are subject to water corrosion and buildup. For those reasons, marine engine oil, with its high anti-corrosion properties, is better suited for boats than regular engine oil used on cars.

Did you like this? Share it: